Akordify

Online Bass Tuner (E A D G)

This free browser tool allows you to tune your bass guitar accurately without needing an account. It detects pitch via your microphone and displays the detected note along with a frequency and cents meter.

How to use this bass tuner

To begin, select the bass instrument and the standard 4-string tuning preset from the available options. Adjust the A4 reference frequency if needed, which defaults to 440 Hz but can be set between 430 and 450 Hz. Click the start button to permit microphone access and play a string firmly to let it ring. The display shows the detected note and a cents meter. If the meter shows a minus sign, the string is flat. A plus sign indicates the string is sharp. Aim for a reading within about 5 cents of the target note. Keep the device near the instrument or your amplifier speaker for the best detection, especially for low frequencies.

Target notes and frequencies

4-string bass standard

StringNoteFrequency (A4 = 440 Hz)
4E141.20 Hz
3A155.00 Hz
2D273.42 Hz
1G298.00 Hz

String numbers follow the usual convention: string 1 is the thinnest full-length string. Frequencies are equal-tempered values for A4 = 440 Hz.

Bass Tuning and Maintenance

Understanding Bass Pitch

A standard 4-string bass is tuned to E1, A1, D2, and G2, starting from the thickest string. These notes are exactly one octave below the lowest four strings on a standard guitar. Because the low E string vibrates at approximately 41.2 Hz, small device microphones may struggle to detect it clearly. To improve accuracy, play the string firmly, ensure the instrument volume is turned up, and keep the tone control open. Placing your device near the amplifier speaker or directly against the instrument body often helps the software register the fundamental frequency more reliably.

Using Harmonics for Precision

When standard open-string tuning remains difficult, the 12th fret harmonic provides a useful alternative. Touching the string lightly above the 12th fret produces a clear E2 note, which is one octave higher than the open E1 string. Because this harmonic sits in a more sensitive frequency range for microphone detection, it often provides a more stable reading. You can use this method to check your tuning at any time. Ensure you allow the string to ring fully after plucking for the best frequency analysis.

Intonation and Tension

Proper tuning also depends on the setup of your instrument. Changing to heavier gauge strings will increase the tension on the neck, which may pull the neck forward and alter your tuning. After installing new strings, it is necessary to tune, let the neck settle, and recheck your work. You can verify your intonation by comparing the 12th fret harmonic with the fretted 12th note. If the fretted note sounds sharp or flat compared to the harmonic, the bridge saddle position requires adjustment to ensure the bass stays in tune across the entire fretboard.

Tuning by Relative Pitch

Learning to tune by ear is a valuable skill for any bassist. The standard method relies on the fourths relationship between strings. Playing the 5th fret of the E string produces an A, which should match the open A string. This pattern continues: the 5th fret of the A string matches the open D, and the 5th fret of the D string matches the open G. Unlike a standard guitar, there is no major third interval to account for, making the pattern consistent across the fretboard.

Harmonics Comparison Method

Another reliable way to tune is using the harmonics method. By lightly touching the string over the 5th fret, you create a harmonic that should be identical in pitch to the harmonic produced over the 7th fret of the next higher string. This method is effective because it removes the influence of fret wear or poor intonation from your tuning process. When the two harmonics sound identical, the strings are in tune with one another. Always recheck your open string tunings after performing these adjustments.

Frequently Asked Questions

Does this tuner support 5-string basses?

This tool currently supports standard 4-string bass tuning. The low B string on a 5-string bass vibrates at approximately 30.9 Hz, which is below the effective range of most standard computer and phone microphones.

What is the A4 reference frequency?

The A4 reference frequency is the standard pitch used to calibrate your instrument. While 440 Hz is the global standard, this tool allows you to adjust it between 430 and 450 Hz to match specific ensemble requirements.

How accurate does the meter need to be?

For most practice applications, a reading within 5 cents of the target frequency is considered in tune. If the meter shows a minus sign, you are flat, and if it shows a plus sign, you are sharp.

Why does my bass sound out of tune after changing strings?

Changing string gauges alters the tension on the instrument neck. This physical shift changes the relief of the neck and can affect tuning stability. After changing strings, tune your instrument, wait for the neck to adjust, and recheck the tuning.